![]() ![]() ![]() This new server is placed inside the LAN zone and it can’t be reached from the rest of my lab (i.e. I cloned existing Contoso Web server, then changed its IP address to 192.168.17.17 and altered the content of its only Web page. I added one more VM – Contoso Intranet server.I made two changes for a better simulation: So yes, you can see those new IPSec configuration screens. The Contoso router is now on the RouterOS version 6.44.5. I will again use the Trange-Frange Company (TFComp) router and Contoso router/LAN. You have been warned! A few important notes about this simulation In case that VPN or encryption technologies are considered forbidden and/or illegal in your country, please stop further reading and leave this page. ![]() Let’s begin!īefore we begin, I need to write a word of caution. This scenario is different than other one described in this article where MikroTik is behind another router, as in this case our MikroTik has a WAN port (like a 3G/4G-LTE or cable modem) with the dynamic IP address, plus there’s a good chance that this address is from the ISP’s private IP address pool.Įven better, in this article I will explain you the concept of a Loopback adapter and how you can use it in situations similar to this one. ip/firewall/nat/add action=src-nat chain=srcnat comment="Hairpin to LAN2" out-interface=bridge-lan-01 src-address=172.16.0.0/23 to-addresses=172.16.0.In this part of the MikroTik IPSec series, I will show you how to establish a Site to Site IPSec tunnel between two routers, when one of them has a dynamic WAN IP address. ip/firewall/nat/add action=masquerade chain=srcnat comment="Masquerade WAN (non-ipsec)" ipsec-policy=out,none out-interface-list=WAN routing/rule/add dst-address=172.16.0.0/23 table=main action=lookup comment="to LAN2" routing/rule/add dst-address=192.168.88.0/24 table=main action=lookup comment="to LAN1" tool/mac-server/mac-winbox/set allowed-interface-list=LANĪdd address=0.0.0.0/8 comment="\"This\" Network" list=BOGONSĪdd address=10.0.0.0/8 comment="Private-Use Networks" list=BOGONSĪdd address=100.64.0.0/10 comment="Shared Address Space. tool/mac-server/set allowed-interface-list=LAN ip/neighbor/discovery-settings/set discover-interface-list=!WAN interface/list/member/add interface=bridge-lan-02 list=LAN interface/list/member/add interface=bridge-lan-01 list=LAN interface/list/member/add interface=pppoe-02 list=WAN comment=PPPoE-02 interface/list/member/add interface=pppoe-01 list=WAN comment=PPPoE-01 interface/list/member/add interface=ether2 list=WAN comment="Uplink WAN for PPPoE-02" interface/list/member/add interface=ether1 list=WAN comment="Uplink WAN for PPPoE-01" interface/list/add name=LAN comment="For Local Area Networks"Īdd disabled=no interface=ether1 name=pppoe-01 add-default-route=no user=fpt1 password=fpt1Īdd disabled=no interface=ether2 name=pppoe-02 add-default-route=no user=vnpt1 password=vnpt1Īdd bridge=bridge-lan-01 interface=ether3Īdd bridge=bridge-lan-01 interface=ether4Īdd bridge=bridge-lan-01 interface=ether5 Send your feedback to /interface/list/add name=WAN comment="For Internet" In this script I assume you have 2 pppoe WAN links: Please try my RouterOS 7 multiwan PPPoE loadbalance scriptġ) This script allows you to send traffic from special address lists via certain pppoe connection, bypassing the load balance logic (for example your TV should always go only via pppoe-02)ģ) This script solves the multiwan issue when you are building outgoing VPN tunnels (openvpn, wireguard, IPSec etc). ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |